Kinetic Friction
steel plates
In this phase of your experiment you will need one long steel plate, one short steel plate, one spring scale, and two 500-gram masses. After calibrating your spring scale, place the short steel plate (rough side down) on top of the longer plate at one end. Then use the string to drag it to the other end at a constant velocity. As you drag the plate, keep the string parallel to the surface of the table and observe the spring scale reading. Repeat three times and record your average reading. Next center a 500-gram mass on the top of the short plate and drag is once again at a constant velocity across the longer plate. Repeat this process three times and record your average spring scale reading. Finally, place two 500-gram masses on top of the short plate and drag is once again at a constant velocity across the longer plate. Repeat the process three times, and record your average spring scale reading in the data table given below.
Data Table I (plate sliding at a constant velocity)
|
EXCEL will now assist with analyzing your data. Minimize your browser, double click My Computer, double click the shared drive called colwell/bay on Lederman, double click your period's folder and then finally double click 1-friction_steel.xls. You will most likely be asked to open the file as "read only" - that is fine. As soon as the file is open, use File Save As to rename the file as
LastnameLastnameFrictionSteel.xls
in your period's folder. This copy of the file now belongs uniquely to your group. Remember that there are to be no spaces in the file name. A printout of this file should be turned in with your lab report.
Refer to the following information for the next question.
For the situation illustrated above, when the plate has both 500 gram masses on top of it, check off which force(s) would belong on a freebody diagram of the plate.
|
wooden block In this phase of the experiment you will need one long wooden board (to serve as an incline plane), one block of wood with one side covered in Teflon, two 200-gram masses, and a meter stick. Place the wooden block (Teflon side down) at one end of the board and measure the distance the block will slide down the board. Then lift the board slowly and record the height above the table when the block first starts to slip. Once the block starts moving, slightly lower the board until the block appears to be move at a constant velocity down the incline. Repeat three times and record the average heights in the table below. Next repeat the experiment three times with a 200-gram mass placed on the block and then again with 400-grams on the block.
Data Table II (block sliding down the incline)
|
|
EXCEL will assist with analyzing your data. Minimize your browser, double click My Computer, double click the shared drive called colwell/bay on Lederman, double click your period's folder and then finally double click 1-friction_wood.xls. You will most likely be asked to open the file as "read only" - that is fine. As soon as the file is open, use File Save As to rename the file as LastnameLastnameFrictionWood.xls in your period's folder. This copy of the file now belongs uniquely to your group. Remember that there are to be no spaces in the file name. A printout of this file should be turned in with your lab report. |
|
|
Refer to the following information for the next question.
For the situation illustrated above, where the wooden block has one 200 gram mass on top of it, check off which force(s) would belong on a freebody diagram of the block.
|
Static Friction In this section of the experiment you will use your knowledge of obtaining the coefficient of kinetic friction on an incline plane to determine the coefficient of static friction between two layers of sand. First fill up a cup with dry sand and slowly pour it onto a piece of paper covering the top of your lab station. Repeat until you get a "nice cone" of sand. Trace out the perimeter of the sand cone and proceed to measure the cone's circumference and height. Once your measurements are completed, return the cup and sand to the white bucket. You will be asked to turn in your "tracing paper" with your lab report. |
|
Your completed lab report will include a title page, a printout of your EXCEL worksheet for the steel plates, a printout of your EXCEL worksheet for the wooden block, and your tracing paper with its calculations for the coefficient of static friction for sand.