Resource Lesson
Rotary Motion
Printer Friendly Version
When an object rotates on an fixed axle (axis) without any translational motion, we look at its rotational kinematics. Consider the pulley in the diagram below. As the mass rises, the string feeds off the edge of the pulley. If the mass rises 20 cm, then 20 cm of string will move along the arc length (edge) of the circle (pulley)
Mathematically, the formula
relates the angle,
, through which the pulley rotates and the arc length,
s
.
For example, if the pulley makes one complete revolution, the arc length,
s
, will equal one circumference,
, while
= 360º or
Substituting these values gives us the equality
Therefore this formula requires that the angle of rotation be measured in radians. Recall from trigonometry that
If a pulley is rotating at a constant rate, we say that it has a constant angular velocity omega,
, which is measured in radians/sec. The equation analogous to s = vt when an object translates at a constant velocity is
.
Let's examine a horizontal turntable rotating at 33
^{1}
/
_{3}
revolutions per minute, or rpm. This is equivalent to
Let's investigate the turntable a little further. Suppose there are three figurines located at three different distances from the center, or axis of rotation, on the surface of the turntable.
Next we want to compare their angular velocities and linear velocities. Since they are on the same rotating platform, all three share the same omega,
. That is, all three revolve through
. However, they each travel through a linear distance based on their unique radius and subsequent circumference. Our new relationship is
.
Therefore, the figurine closed to the center has the least linear velocity (speed in m/sec) while the figurine closest to the edge has the greatest linear velocity. In the picture below, four students are on a rotating merry-go-round. The student at the bottom right has the greatest linear velocity while the two students curled forward on the left have equal but smaller linear velocities.
image courtesy of
http://ligiatcolindres.blogspot.com/2013/05/torque.html
Now let's suppose that we have two pulleys which share a common belt that passes along their circumferences.
image courtesy of
http://tech.texasdi.org/gearsandpulleys
One pulley is called the driving pulley (usually connected to a motor) while the other is called the driven pulley. The common belt assures that the perimeters of both pulleys have the same linear velocity. Since the pulleys have different radii, one pulley must be rotating faster, or have a greater angular velocity.
This result tells us that if the large pulley has a radius that is three times that of the small pulley, the small pulley must be rotating (spinning) three times faster than the large pulley.
Now let's examine a situation in which a wheel is being "brought up to speed." That is, you want to increase the wheel's angular velocity. To change a rotating object's angular velocity means that you want it to accelerate. From linear motion we know that net F = ma, that is, a force is required to change an object's translational velocity. Therefore, rotationally, we need a torque to be applied.
Recall that the formula to calculate torque is
, which can be rewritten in terms of the sine of the angle between the line of action of the force vector and the radius. We usually expressed the formula as
The analogous equation for net F = ma is
where
I
is the moment of inertia of the rotating mass and alpha,
, is the angular acceleration, or the rate at which the angular velocity changes. The angular acceleration is measured in rad/sec
^{2}
.
Related Documents
Lab:
Labs -
A Physical Pendulum, The Parallel Axis Theorem and A Bit of Calculus
Labs -
Conservation of Momentum in Two-Dimensions
Labs -
Density of an Unknown Fluid
Labs -
Mass of a Paper Clip
Labs -
Moment of Inertia of a Bicycle Wheel
Labs -
Rotational Inertia
Resource Lesson:
RL -
A Chart of Common Moments of Inertia
RL -
A Further Look at Angular Momentum
RL -
Center of Mass
RL -
Centripetal Acceleration and Angular Motion
RL -
Discrete Masses: Center of Mass and Moment of Inertia
RL -
Hinged Board
RL -
Introduction to Angular Momentum
RL -
Rolling and Slipping
RL -
Rotational Dynamics: Pivoting Rods
RL -
Rotational Dynamics: Pulleys
RL -
Rotational Dynamics: Rolling Spheres/Cylinders
RL -
Rotational Equilibrium
RL -
Rotational Kinematics
RL -
Rotational Kinetic Energy
RL -
Thin Rods: Center of Mass
RL -
Thin Rods: Moment of Inertia
RL -
Torque: An Introduction
Worksheet:
APP -
The Baton Twirler
APP -
The See-Saw Scene
CP -
Center of Gravity
CP -
Torque Beams
CP -
Torque: Cams and Spools
NT -
Center of Gravity
NT -
Center of Gravity vs Torque
NT -
Falling Sticks
NT -
Rolling Cans
NT -
Rolling Spool
WS -
Moment Arms
WS -
Moments of Inertia and Angular Momentum
WS -
Practice: Uniform Circular Motion
WS -
Rotational Kinetic Energy
WS -
Torque: Rotational Equilibrium Problems
TB -
Basic Torque Problems
TB -
Center of Mass (Discrete Collections)
TB -
Moment of Inertia (Discrete Collections)
TB -
Rotational Kinematics
TB -
Rotational Kinematics #2
PhysicsLAB
Copyright © 1997-2023
Catharine H. Colwell
All rights reserved.
Application Programmer
Mark Acton